Tag Archives: Parts pricing

AG200 parts suppliers.

I get asked a lot about where to get parts for the AG200. Everyone knows that Yamaha parts are expensive in Australia, but so is everything else right? Our strong, unionised workforce and accompanying high minimum wage is the price we pay right? You have to pay to play right? RIGHT?! Lets take a closer look…

OK, so the hard numbers first. A few posts back I did a write-up on a basic, top end rebuild and the parts that are required. As a service to my beloved readers (actually it was for a farmer who reached the “service interval” of his bike! ūüôā ) I went out and purchased these parts from my local Yamaha dealer.

1NU-11181-00       GASKET, CYLINDER HEAD 1  Р$21.51

90430-14131          GASKET  Р$14.10

93211-45471          O-RING  Р$17.35

93210-57634             O-RING x 2  Р$9.00 each

93210-72529           O-RING  Р$14.30

5LB-11351-00         GASKET, CYLINDER Р$8.05

93210-13361           O-RING  Р$1.90

5H0-12119-00        SEAL, VALVE STEM x 2  Р$6.60 each

93210-09165          AA5 O-RING Р$2.60

4BE-15451-03        GASKET, CRANKCASE COVER 1  Р$15.25

93210-14369          O-RING  Р$4.50

93210-32172          O-RING  -$4.15

94580-41104          CHAIN (DID25SH 104L) Р$77.70

4FM-1 2213-00      GASKET, TENSIONER CASE  Р$1.30

15A-11603-00        PISTON RING SET (STD) Р$71.70

93450-17044         CIRCLIP x 2  Р$3.90

So the total for the above parts in Australia for a basic, top-end overhaul for an AG200 comes to $289.51. The same sixteen line items for a 2017 TW200 from Partshark in the US is $164.31US. So if you do the conversion at the time of writing, it comes to $216.89 in AU dollars and then you have to freight it out here. So if the freight is around $50 AU you can see that it pretty much doesn’t add up to get it from the US. I don’t think it is anyway.

Even back in the days not too long ago when the US and AU dollar was close to parity, I was noticing a disturbing trend from the few things I was getting from the US but particularly from a lot of my acquaintances and other Australians that I had contact with on forums. People were getting the wrong parts or even broken ones. Were unscrupulous US companies/parts guys using us as a dumping ground for all their crap parts and products? My experience was yes, yes they were. They knew we wouldn’t send them back, we are not value Nazis like the average US shopper and even if we were, we were not going to wear the freight to send it back over the pond anyway! I wonder how many second-rate or wrong bits ended up on Ebay over here because of this?

I lost interest in ordering a lot of parts direct from the US after noticing all this, while the strengthening of the US dollar and a price reduction on parts from Yamaha Australia helped to close the gap anyway. So my recommendation is to make sure you do the math before you go ordering stuff from the US, it’s not worth it any more in my opinion, not for one-off rebuild parts anyway. If you are going to buy a heap of one part then it may be a different story.

So what do I recommend for us Aussies? Shop around! A lot of dealers did not pass on the Yamaha price reductions from a few years ago so you might find a fair bit of variation for the sake of a few phone calls. Here’s one trick you can try; ask for a price on the good old NGK D8EA spark plug for the AG200. Who ever is cheapest for this simple part will usually be the cheapest for everything. Why? Because most (not all) dealers usually set a margin for their parts in their accounting software that covers all their stock (if they have a computer, I know dealers who still don’t!) so if they are cheapest on this easy to remember, common part then they usually are across their whole stock of bits.

What about after-market bits? The big one in my list above is the cam chain. A good quality DID or RK chain can be had for half the price of the one listed above. The rest…well I have always liked genuine Yamaha parts and as ridiculous as the prices are for for some of the o-rings listed here, not all rubbers are created equal. I get using generic, bearing shop o-rings (I still wont use them though) for the external, easy to replace parts like the rocker covers and top timing gear cover o-rings but the internal ones? Don’t do it unless you are a materials engineer who knows what heat and hydro carbons do to the materials you are going to use!

How about after-market gaskets? Same deal for me, I go with genuine but I’m sure there are good after-market options out there, you just have to troll forums and see what people are using and have had good results with. It is an area that I should look into more and try some variations.

So bottom line for me is shop local. I have been on the other side of the counter and it is a tough gig these days. With the pitiful margins on bikes and with the floor plans the manufacturers impose on their dealers, I wonder how they (particularly the smaller ones) survive. So help them out if you can, ask them for a discount – they can only say no and you may be helping them keep their doors open for your future convenience!

Cheers

AGman